Vermont Castings DBR39 Provozní pokyny

- 1 -INSTALLER: DO NOT DISCARD THIS MANUAL - LEAVE FOR HOMEOWNER1000278806/00 Rev. 0BuilderRear VentDirect VentModelsDBR33DBR36DBR39DO NOT STOREOR U

- 10 -Fig. 13*IMPORTANT* DIRECT THROUGH SIDEWALLNote:Vent Starter Kit Model 7DVRVT must be used in straight out the wall rear vent applications.Maxim

- 11 -Measure wall thickness and cut adjustable zero clearancesleeve parts to proper length (MAXIMUM 12"/305mm).Adjust sleeve to maximum (10-3/8

- 12 -The maximum horizontal vent run is 20 feet (6100mm)when the vertical vent rise is 7.5 feet (2286mm). Fig. 19Fig. 19VERTICAL SIDEWALL APPLICATI

- 13 -HORIZONTAL DIMENSIONSEE PAGE 15 FOR VENTINGREQUIREMENTS FOR SNORKELS.34567891011121314151617181920212223242526272829303 4 5 6 7 8

- 14 -COMBUSTIBLE WALLS (Fig. 25): Cut a 9-3/8"H x 9-3/8"W (240mm x 240 mm) hole through the exterior wall and frame as shown(Fig. 24).NON-

- 15 - STEP 4(Fig. 28) Measure the horizontal length requirementincluding a 2" (50mm)overlap, i.e. from the elbow to theoutside wall finish plu

- 16 -DO NOT BACK FILL AROUND SNORKEL.SOIL SHOULD NOT BE LESS THAN 4"(100mm) BELOW SNORKEL.FOUNDATION RECESS SNORKEL SCREWSWALLSCREWSSHEET METALW

- 17 -Fig. 39Clearance above a roof shall extend a mini-mum of 24" (610mm) above the highest pointwhen it passes through the roof surface, andany

- 18 -GLASS FRAME REMOVAL1. Shut off gas.2. Let the fireplace cool if it has been operating.3. Remove top louvre. (See Louvre Removal)4. Open the lowe

- 19 -1 . Remove front glass. (See "Glass Removal" Section)2. Remove logs from the packaging.As with all plastics — these are not toysand sh

- 2 -TABLE OF CONTENTSPLEASE READ THE INSTALLATION & OPERATING INSTRUCTIONS BEFORE USING APPLIANCE.IMPORTANT: Read all instructions and warnings

- 20 -The burner and control system consists of:• burner tube • gas orifices• pilot assembly • thermopile• millivolt gas valveMost of these compo

- 21 -TO TURN OFF GAS TO APPLIANCE4. Push in gas control knob slightlyand turn clockwise to"OFF". Do not force.5. Close control access

- 22 -TROUBLE SHOOTING THE GAS CONTROL SYSTEMSIT 820 NOVA MILLIVOLT VALVESTART CHECKGLASS DOOR TO BE REMOVED BEFORE SERVICE WORKGAS SUPPLY ON• SHUTOF

- 23 -GAS SUPPLY ON• SUPPLY LINE HOOKED UP• SHUTOFF VALVE OPENNONONONO• LOCKOUT HAS ENGAGED. WAIT 60 SECONDS AND TRY AGAIN.• PIEZO NOT TIGHT ENOUGH

- 24 -REPLACEMENT PARTS LIST - REAR BUILDER SERIESDESCRIPTION DBR33 DBR36 DBR391. Log Set Complete 10000470 10000023 100000241a. Log Front Left BA2 BB

- 25 -FOR FIREPLACES EQUIPPED WITH SIT 820 MILLIVOLT GAS VALVE23222021186 a/b151398 a/b121114a/b272829262625171916 a/b7 a/b30232432314a/b51034 a/b8 a/

- 26 -WIRING INSTRUCTIONSOPTIONAL FAN KIT - FK12 and FK24FK12This auxiliary fan system increases the efficiency of thecirculation of the heating air.T

- 27 -6. Hang Bay Window Frame assembly over existing glassframe.Do not remove existing glass frame7. Re-install top louvre assembly.Remove all plasti

- 28 -OPTIONAL CERAMIC REFRACTORYINSTALLATIONOPTIONAL SCREEN KIT INSTALLATIONTo install the Frame Window Screen:WARNING: DO NOT install the framewindo

- 29 -CRIMPED ENDS VENTING COMPONENTS7DVRVT - Through the wall Rear Vent TerminationStarter Kit -Model 7DVSK - Sidewall VentingStarter Kit - Model 7TD

- 3 -IMPORTANT:PLEASE REVIEW THE FOLLOWINGCAREFULLYRemove any plastic from trim parts before turningthe fireplace ON.It is normal for fireplaces fabri

- 30 -TWIST LOCK VENTING COMPONENTSStarter Kit -Model 7TDVSK - Sidewall VentingStarter Kit - Model 7TDVSKV - Vertical Ventingfor 7TDVSKV-A order 1/12

- 31 -

- 32 -410 Admiral Blvd. • Mississauga, Ontario, Canada L5T 2N6 • 905-670-7885 www.vermontcastings.comCFM Majestic, Inc.© CopyrightCFM Majestic, Inc.10

- 4 -A 36" 914mmB 34 1/4"870mmC 21" 533mmD 33" 838mmE 24" 610mmF 16" 406mmG 19" 483mmH 23 7/8"606mmI 27 1/2&qu

- 5 -Ref. Mantel Ref. Mantel From Mantel Leg fromDepth Top Louvre Fireplace SideV 10" (254 mm) A 12" (305 mm) 10" (254mm)W 8" (

- 6 -Do not use this fireplace if any part of it hasbeen under water. Immediately call a qualifiedservice technician to inspect the fireplaceand repl

- 7 -When using copper or flex connector use only approvedfittings. Always provide a union so that gas line can beeasily disconnected for burner or f

- 8 -GENERAL INFORMATION ON ASSEMBLINGTHE VENT PIPESJoin pipes and secure joints with three (3) sheetmetalscrews. (See Fig. 10) Wipe off excess seal

- 9 -VVVVVVVVVXXXDEBBBCBMBAJKAFLGGTERMINATION CAP AIR SUPPLY INLET GAS METER RESTRICTED AREA(TERMINATION PROHIBITED)HIFixedClosedFixedClosedOpenableOp